Manage cookies
Cookie Settings
Cookies necessary for the correct operation of the site are always enabled.
Other cookies are configurable.
Other cookies are configurable.
Request Product Information
Interested in learning more about this product or need a custom solution? Please fill out the form below, and our team will get back to you promptly.
Card Guides, Keyable, 4HP, IEEE 1101.10
PCB ESD clip for card guides
- Material : Stainless Steel
- ESD (Electrostatic Discharge) clips for CG3 series card guides provides permanent electrostatic discharge of the PCB before and after mate with connector
- Snap-in mount to either end of CG3 card guides
PCB ESD clip for card guides
- Material : Polycarbonate UL 94-V0, Color : Blue
- To conceal unused slots and prevent airflow.
- Snap-fit onto keyable card guides in unused slots.
- Suitable for all 4HP x 160MM standard guide rails (not offset).
- This air blocker does not fit with EMC Rugged Subracks (CCA60 thru CCA95) and extrusion rails (1440-0131, 1440-0132)
160mm, 0.5HP (0.100") offset, for Plug-in Power Supplies
- IEEE 1101.10 compliant, 4HP wide
- Material : Polycarbonate, PC GF20, UL94V-0
- 0.5HP (0.100") offset
- For 0.062" to 0.100" thick cards
- Snap-in mount
- Available in Green color only
160mm, 220mm, Injection Molded Coding keys for CG3-Series Keyable Card Guides
- Material : Polycarbonate, PC GF20, UL94V-0
- Keys are used for keying plug-in assemblies such as front panels and prevents them from being used in incorrect slots. These keys are installed in front chambers of CG3 series card guides and matched with an offsetting key inserted into type IV injector/ejector handles. By keying upper and lower card guides, over 4000 combinations are possible.
- Snap-in mount to square chambers of card guide/handle click on image to enlarge detail
- Available in Grey and Red color
80mm, Injection Molded for RTM
- IEEE 1101.10 compliant, 4HP wide
- Material : Polycarbonate, PC GF20, UL94V-0
- For 0.062" to 0.100" thick cards
- For 80mm RTM (Rear Transition Module)
- Screw-in mount
- Comes with self tapping screw for attachment to horizontal extrusion rails
- Available in Grey color only
160mm, 220mm, Injection Molded
- IEEE 1101.10 compliant, 4HP wide
- Material : Polycarbonate, PC GF20, UL94V-0
- For 0.062" to 0.100" thick cards
- Available for 160mm and 220mm depth Eurocard
- Snap-in mount
- Available in Grey and Red color
Request Product Information
Interested in learning more about this product or need a custom solution? Please fill out the form below, and our team will get back to you promptly.
Request Product Information
Interested in learning more about this product or need a custom solution? Please fill out the form below, and our team will get back to you promptly.
Request Product Information
Interested in learning more about this product or need a custom solution? Please fill out the form below, and our team will get back to you promptly.
Request Product Information
Interested in learning more about this product or need a custom solution? Please fill out the form below, and our team will get back to you promptly.
Request Product Information
Interested in learning more about this product or need a custom solution? Please fill out the form below, and our team will get back to you promptly.
Request Product Information
Interested in learning more about this product or need a custom solution? Please fill out the form below, and our team will get back to you promptly.
Request Product Information
Interested in learning more about this product or need a custom solution? Please fill out the form below, and our team will get back to you promptly.